How To Set The Pool Timer

Download Commodity

Download Commodity

An Intermatic timer is a timer that you can install in your home and connect to annihilation with a power source, such as lights, to programme them to turn on and off at certain times of day. The two types of Intermatic timers are analog and digital. They are both easy to set, every bit long as yous make sure to follow the steps and set the correct times.

1. 1

   Open upwardly the door on the timer's enclosure. Y'all don't need any tools to open up the enclosure. Use your hands to pry open up the door on the greyness box that encloses the timer.^[1]

   • This applies to Intermatic Mechanical Time Switch models with an all-metal structure.

2. 2

   Rotate the clock then that the large arrow points to the electric current time. Turn the xanthous clock dial clockwise with your paw until the large arrow facing downwardly points at the electric current time. It's important to set this time as accurately as possible so that the timer works at the exact times y'all desire it to.^[2]

   • The punch only turns clockwise, so if you pass the correct fourth dimension just keep turning information technology until you get in that location once again.
   • Each line between numbers on the clock represents an interval of twenty minutes.
   • Don't e'er unscrew the arrow for the electric current time or you will throw off the timer.

   Advertisement

3. 3

   Loosen the "on" and "off" arrows with your fingers or pliers. Plow the knobs on the arrows to the left to loosen them. Utilise a fix of pliers to become them started if they are too tight to loosen with your fingers.^[three]

   • These are the arrows you will prepare at the times you desire the timer to turn something on and off.

4. iv

   Slide the "on" and "off" arrows to the times you want them gear up at. Slide the arrow that says "on" to the fourth dimension you want the timer to plow something on at. Slide the "off" pointer to the time yous want information technology to plow off at.^[four]

   • If you want your timer to turn your lights on at dawn and dusk, then do a quick Internet search for the dawn and sunset times in your surface area and set the arrows to those.

5. five

   Tighten the knobs on the "on" and "off" arrows with your fingers. Screw the arrows in place as tight every bit yous can with your fingers. Employ pliers to tighten them all the mode if they still slide subsequently y'all tighten the knobs with your fingers.^[five]

Advertisement

1. one

   Printing and hold the "on/off" push button and press the reset push button with a paperclip. Flip open the door that covers the buttons so agree the "on/off" push as you press the reset button in with a paperclip for 3 seconds. Keep holding the "on/off" button for some other 3 seconds.^{[half dozen]}

   • This will clear the timer's memory and let you lot programme it from the start.

2. 2

   Press the "manner" button until the screen shows "setup", then printing "on/off". This will enter the setup carte du jour. From here y'all will brainstorm to set the current hour.^[7]

   • Y'all should encounter the hr flashing on the digital brandish at this bespeak.

3. 3

   Ready the current hour and minutes. Utilise the plus and minus keys to ready the current hr, then hit the "on/off" button. Prepare the current minutes with the plus and minus keys, followed by the "on/off" button.^[8]

   • Brand sure to pay attention to whether the time yous are setting is AM or PM.

4. 4

   Set the current twelvemonth, month, and engagement. Use the plus key to set the current yr, then printing "on/off" to move on. Do the same for the month and date.^[ix]

   • You can hold down the plus or minus keys to change the numbers a bit faster.
   • When you lot are done with this, you lot volition see a day of the week displayed. If the day is wrong, then you may accept set up the engagement wrong and you will have to repeat the steps. If the day is right, hit "on/off" to move on.

5. 5

   Select manual or machine daylight savings and your zone. Leave the daylight savings setting on motorcar if you utilise daylight savings in your area. Change information technology to manual if yous practice not use daylight savings. Refer to the map in the instructions to encounter which zone you fall into and set the correct 1.^[10]

   • Always use the "on/off" button to move on to the next section of the programming.

6. 6

   Adjust the dawn and dusk times as needed. The next hour y'all will come across is the timer's estimated dawn time for your expanse. Adapt it if information technology is off, and then move on to the dusk time and exercise the same.^[11]

   • These are the times that the timer will follow to turn on and off.
   • This is the stop of the bones setup and you will exist taken back to the beginning of the setup screen when you are done.

7. 7

   Press the "fashion" push until it displays "PGM", then hit "on/off". This will take you into the program menu and so you tin set up the timer's on and off events. The timer is automatically set to turn on at dusk and off at dawn every day of the week. Change these settings if y'all want, or leave them the same if this works for yous.^[12]

   • When y'all are happy with the settings, just press "fashion" once again to put the timer back in "Machine" way and close the cover over the buttons.

Advertisement

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertisement

Cheers for submitting a tip for review!

Near This Article

Thank you to all authors for creating a folio that has been read 25,233 times.

Did this commodity help you lot?

Source: https://www.wikihow.com/Set-an-Intermatic-Timer

Share this post